How to Install a Bathtub
How to Install a Bathtub
Blog Article
Here down the page you will find some worthwhile advice pertaining to A Step-by-Step Guide to Installing a Bathtub.
Setting up a bath tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the project can relocate speedily; if you have to open a wall surface to eliminate the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Make sure you have actually certified yourself for the work and are comfortable trying it. As opposed to working with a specialist to take control of a halfway-completed project, it is much better to take into consideration using one before you start. Chances are you may require a professional plumber to make tube connections.
This write-up will assist you mount a brand-new bathtub in your shower room if you have actually already acquired a new tub as well as do not require to change the plan of your previous water pipes.
Your tools and material list need to consist of the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the restricted accessibility that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are practical in equally spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub till the level reviews level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Activate the water system as well as inspect all joints as well as new pipework for leakages as well as tighten them if required. Fill the tub and additionally inspect the overflow outlet and also the typical electrical outlet for leaks.
Finally, repair the bath paneling as defined in the producer's user's manual. Tiling and also securing around the tub must wait till the bath tub has been used a minimum of when as this will resolve it right into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet as well as the sink. Safeguard the faucet in place with the maker supplied backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former kind should be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, triggering the water to pass through the wall in between the bathroom and the tiling, bring about complications with moisture and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can split rather early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for taking a few minutes to read our post. Do you know another individual who is serious about the subject? Please feel free to share it. Many thanks for your time spent reading it.
Schedule Services
Report this page